[logo_carousel_slider].

Newton 106 Flexproof

Adam Lowe

Newton 106 FlexProof is a highly advanced, single component, waterproofing compound for the waterproofing of joints that is supplied in two variants: Newton 106 FlexProof-X1 is a highly viscous, thixotropic paste that is suitable for the waterproofing of construction and vertical movement joints, whilst Newton 106 FlexProof-NV has a lower viscosity and so is pourable and better suited where the application is to horizontal movement joints. Both variants form an elastomeric polymer that is rainproof in minutes and capable of handling severe building movements and deformations. With a superb bond to most building materials and with very high levels of flexibility, Newton 106 FlexProof is capable of resisting both negative side and positive side water-pressure at construction joints, even where movement is expected. The product has the ability to remain watertight against positive pressure even when resisting 20% expansion and compression and 10% shear, and so is especially useful where waterproofing is required within movement joints and at the interfaces of differing materials. Backed by extensive MFPA test data, Newton 106 FlexProof is also a constituent part of the Newton HydroBond System, which is supported by BDA Agrément® BAB 17-031/04/A.

Newton 110 WATstop

Adam Lowe

Manufactured by Diasen S.R.L. of Sassoferrato, Italy, Newton 110 WATstop is a three-component, fibre-reinforced cement/epoxy product that, when mixed, produces a workable mortar suitable for surface repair and surface smoothing. With the addition of up to 40% water, a paint/slurry-like consistency can be achieved that is suitable for numerous applications including the damp proofing of walls and slabs and the waterproofing of concrete structures, as well as being a primer for a number of Newton System 100 Liquid Waterproofing products.

Newton 109-LM

Adam Lowe

Newton 109-LM is a radon gas certified, flexible, single-component, cold-applied, seamless rubber waterproofing membrane used primarily for the external waterproofing of earth retaining structures such as basements and foundation walls. Newton 109-LM is also adept as a detailing membrane for the termination and jointing of other Newton waterproofing products, and is the perfect primer for the adhesion of butyl products to concrete and mortar. Newton 109-LM is extremely puncture resistant with elasticity of 850% and a 95% recovery memory. The membrane becomes fully engaged into the substrate to prevent water tracking and is suitable for all below-ground and earth-retained structures, ranging from domestic basements to the largest civil engineering projects. Newton 109-LM is available in two variants: Medium Viscosity, for use in warmer temperatures, and Low Viscosity, for when it is cooler. Newton 109-LM is also a constituent product of the Newton HydroBond® System supported by BDA Agrément® BAB 16-031/03/A and is accepted by the NHBC as a suitable waterproofing system for Type A Waterproofing to Grades 1, 2 and 3 – BS 8102:2009.

Newton 203-RM

Adam Lowe

Newton 203-RM is a single-component, fast-setting, Portland cement-based structural mortar, used primarily for the durable repair of concrete. Setting in just 10 minutes at 20ºC, Newton 203-RM is ideal for areas that cannot be taken out of service for long periods, or where the concrete is subjected to heavy wear such as roads, runways, bridges, decks, floors and footpaths. Polymer-modified, and fibre-reinforced, Newton 203-RM is physically and chemically compatible with the host concrete, quickly exhibiting high adhesive and compressive strength. As a single component, requiring only the addition of water, the resulting mortar is rapid curing with enhanced polymeric properties and reliable strength development which is not significantly affected by low temperature use. The mortar can be used as supplied up to 100 mm deep, or bulked out with clean, washed, sharp sand to form a high performance screed or for floor or deck repairs up to maximum depth of 300 mm.

1 3 4 5